K3 and Signallink next the Microham

classic Classic list List threaded Threaded
4 messages Options
Reply | Threaded
Open this post in threaded view
|

K3 and Signallink next the Microham

Ross Biggar
Thanks for all the comments about the signal link.
I found the problem when checking Airlink express, I had the volume and tx levels set to almost zero, in Airlink express so whenI reset them to max, everything popped into life and all my other digital programs then worked perfectly.

Next to try and set up the microham for digital work.
All advice very gratefully accepted.
Thanks
Ross
ZL1WN
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]
Reply | Threaded
Open this post in threaded view
|

Re: K3 and Signallink next the Microham

Mike Reublin NF4L
Why would you use two interfaces for digital?

73, Mike NF4L

> On May 29, 2016, at 6:54 PM, Ross <[hidden email]> wrote:
>
> Thanks for all the comments about the signal link.
> I found the problem when checking Airlink express, I had the volume and tx levels set to almost zero, in Airlink express so whenI reset them to max, everything popped into life and all my other digital programs then worked perfectly.
>
> Next to try and set up the microham for digital work.
> All advice very gratefully accepted.
> Thanks
> Ross
> ZL1WN
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]
Reply | Threaded
Open this post in threaded view
|

Re: K3 and Signallink next the Microham

Joe Subich, W4TV-4
In reply to this post by Ross Biggar

 > Next to try and set up the microham for digital work.

Which microHAM Interface?

In general, set the K3/K3S to DATA mode and select MENU:MIC SEL =
LINE IN, set Mic Gain (LINE) to about 15 and configure the microHAM
interface audio levels as documented in the "Setting Audio Levels"
section of the microHAM Users Manual.  As a final "touch up" adjust
the K3 "Mic Gain" for four bars of ALC (the fifth bar can flicker).


73,

    ... Joe, W4TV

On 5/29/2016 6:54 PM, Ross wrote:

> Thanks for all the comments about the signal link.
> I found the problem when checking Airlink express, I had the volume and tx levels set to almost zero, in Airlink express so whenI reset them to max, everything popped into life and all my other digital programs then worked perfectly.
>
> Next to try and set up the microham for digital work.
> All advice very gratefully accepted.
> Thanks
> Ross
> ZL1WN
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]
Reply | Threaded
Open this post in threaded view
|

K3 and Signallink next the Microham

Ross Biggar
Thanks for the comments.
The Microham is the Keyer II.
I have connected the line in,line out and the usb cable to the pc, are there
any other connections I need to make??
Yes the multicore cable from the k3 is the one for the k3 it is marked k3.
Thanks
Ross
-----Original Message-----
From: Joe Subich, W4TV
Sent: Monday, May 30, 2016 2:21 PM
To: [hidden email]
Subject: Re: [Elecraft] K3 and Signallink next the Microham


> Next to try and set up the microham for digital work.

Which microHAM Interface?

In general, set the K3/K3S to DATA mode and select MENU:MIC SEL =
LINE IN, set Mic Gain (LINE) to about 15 and configure the microHAM
interface audio levels as documented in the "Setting Audio Levels"
section of the microHAM Users Manual.  As a final "touch up" adjust
the K3 "Mic Gain" for four bars of ALC (the fifth bar can flicker).


73,

    ... Joe, W4TV

On 5/29/2016 6:54 PM, Ross wrote:

> Thanks for all the comments about the signal link.
> I found the problem when checking Airlink express, I had the volume and tx
> levels set to almost zero, in Airlink express so whenI reset them to max,
> everything popped into life and all my other digital programs then worked
> perfectly.
>
> Next to try and set up the microham for digital work.
> All advice very gratefully accepted.
> Thanks
> Ross
> ZL1WN
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]